Tube Seam Anchor OverviewWorking Principle of Pipe Seam AnchorWhen a slotted anchor is installed in a hole smaller than the diameter of the pipe, three forces are exerted on the surrounding rock: radial pressure on the hole wall over the entire length of the slotted anchor, friction to stop the surrounding rock from sliding down the hole, and the support force of the slotted anchor pallet, which makes the surrounding rock more stable.Specification of Slit Anchor1、Outside diameter (mm):φ33,φ40,φ43 (0.5).2、Length-(mm):-1200、1500、1800、2000、2500,3, Material: Q235, 16Mn, 20 Mnsi.Technical requireme
Contact Now
Product Details of Tabung Baja Berkekuatan Tinggi Dengan Celah Memanjang Untuk Memperkuat Batuan Perimeter Di Pertambangan MF33 MF40 MF43Hollow anchor rod is a diploma of metallic plate rolled into a longitudinal slit with a tubular rod, with a rock drill forcibly pressed than the diameter of the rod small borehole (with a difference of 2 ~ 3mm), may be straight away alongside the hollow to the 80 ~ 100cm range of radial stress at the hollow wall and the friction produced thru the layer to save you the encompassing rock sliding down, coupled with the anchor tray tray bearing force.
Contact Now
Product DescriptionMain technical performance: Initial anchoring force: 3~7 tons; Pipe ring pull-off load: 8~10 tons; Anchor pipe pull-off resistance: 12~13 tons; Corrosion resistance is 20~30% higher than that of A3 steel, which is conducive to long-term use.Specifications and parametersMain Specifications: MF43 MF40 MF33Length (mm): 1200, 1500, 1800, 2000, 2500Material: Q235, 16Mn（Q345 Q355）, 20 Mnsi.Technical features1. the uncooked cloth adopts high-strength alloy strip steel;.2. Simplest installation.3. No anchoring agent required.4.
Contact Now
Details of Pipe Seam AnchorPipe seam anchor is a full-length anchoring, active reinforcement of the surrounding rock of the new anchor, its three-dimensional part is a longitudinal slit of high-strength steel pipe, when installed in a slightly smaller than the diameter of the pipe drilling, can immediately in the full-length range of the radial pressure on the hole wall and prevent the surrounding rock sliding friction, plus the anchor tray pallet bearing force, so that the surrounding rock is in a three-way state of force, and to achieve the rock layer great.
Contact Now
Product DetailsHollow anchor rod is a diploma of metallic plate rolled into a longitudinal slit with a tubular rod, with a rock drill forcibly pressed than the diameter of the rod small borehole (with a distinction of two ~ 3mm), can be at once alongside the gap to the eighty ~ 100cm vary of radial strain on the gap wall and the friction produced via the layer to stop the surrounding rock sliding down, coupled with the anchor tray tray bearing force.
Contact Now
Details of Pipe Seam AnchorPipe seam anchor is a full-length anchoring, active reinforcement of the surrounding rock of the new anchor, its three-dimensional part is a longitudinal slit of high-strength steel pipe, when installed in a slightly smaller than the diameter of the pipe drilling, can immediately in the full-length range of the radial pressure on the hole wall and prevent the surrounding rock sliding friction, plus the anchor tray pallet bearing force, so that the surrounding rock is in a three-way state of force, and to achieve the rock layer great.
Contact Now
Description of Sewn Tube AnchorCompared with the traditional shelf support, because the support material used in anchor support is less, lighter weight, roadway excavation, reducing the amount of support material transportation, labor intensity is also greatly reduced, and is conducive to improving the efficiency of excavation.
Contact Now
Anchor Tray DescriptionMining pallet is mainly used for fixing between the top and bottom of the coal seam, mining pallet is a longitudinal slit high-strength steel pipe, anchor rod pallet manufacturer production, when installed in the drill hole slightly smaller than the diameter of the pipe, it can be immediately in the full length of the hole wall to exert radial pressure and stop the friction of the surrounding rock sliding down the hole wall, coupled with the support force of the anchor pallet pallet, so as to make the surrounding rock in a three-way force state.
Contact Now
Product Description：Our Rock Bolt In Tunnel range is an advanced solution designed for the reinforcement of tunnel structures. These include the Pipe Seam Anchor Rod, which provides strong support at the joints of the tunnel tubes, ensuring a solid and reliable tunnel structure, and the Rock Anchor Split technology, which provides long-lasting support at the rock split face, enhancing the overall safety of the tunnel.
Contact Now
Product DescriptionHollow anchor rod, also called rock stabilizer, is an advanced material essential for underground support. Pipe slit anchor is a highly specialized support item, which is an advanced material used for underground culvert roof and other engineering support.Specifications and parametersMain Specifications: MF43 MF40 MF33Length (mm): 1200, 1500, 1800, 2000, 2500Material: Q235, 16Mn（Q345 Q355）, 20 Mnsi.Technical features1. the uncooked cloth adopts high-strength alloy strip steel;.2. Simplest installation.3. No anchoring agent required.4.
Contact Now
Description of Anchor Tray for Coal MiningMining pallet is mainly used for fixing between the top and bottom of the coal seam, mining pallet is a longitudinal slit high-strength steel pipe, anchor rod pallet manufacturer production, when installed in the drill hole slightly smaller than the diameter of the pipe, it can be immediately in the full length of the hole wall radial pressure and friction to stop the perimeter rock from sliding down, coupled with the anchor pallet pallet bearing force, so as to make the perimeter rock in a three-way force state.
Contact Now
Raw Material SelectionThe raw material is high-strength alloy strip steel, here are Q235, 16Mn, 20 Mnsi and other raw materials to choose fromSpecificationDiameter(±0.5)33mm39mm 40mm42mm46mm47mmLength(±0.5)1.2m1.5m1.9m2.0m2.5m3mMining Plate(±0.5)140*140*6mm,150*150*5mm,200*200*10mmMaterialQ235，16Mn，20 MnsiWeldingThe retaining ring interface has no cracks, no slag inclusions, and no burning through the pipe wallAssembleRetaining ring and Split Sets Anchor body to assembleQuality ControlAfter the product is assembled, the quality controller will inspect the quality of the product, and the p
Contact Now
Details of Pipe Seam AnchorA slit-tube metal anchor is a type of anchor manufactured by means of rolling and pressing sheet metal into a tubular rod with longitudinal slits. It can be drilled through a rock drill into a hole smaller than the diameter of the anchor to apply direct radial pressure and create resistance through the layers to prevent sliding of the surrounding rock. At the same time, the anchor tray pallet provides additional support.
Contact Now
Product Details:Slit Tube Metal Anchor is an anchor product manufactured through the use of sheet metal rolled and pressed into a tubular rod with longitudinal slits. This type of anchor prevents the surrounding rock from sliding by drilling holes into the rock that are slightly smaller than the diameter of the anchor, realizing that radial pressure is exerted around the holes and generating friction.
Contact Now
Product Description:Left-handed anchor rods, for roadway support, are characterized by high strength, reasonable structure and large preload force. Left-handed anchor can increase the binding force on the surrounding rock, and the installation is mechanized, which is easier and faster. Lefty anchors can be end anchors, extension anchors and full anchors. According to the steel grade, the left-hand anchor is classified as MG335/MG500/MG600, and the diameter of the rod body is from 16mm to 22mm, which can also be processed according to the construction requirements.
Contact Now
Slit Tube Anchor OverviewSlit pipe metal anchor is a diploma of metal plate rolled and pressed into a tube with longitudinal seams,it is a new sort of self-anchoring anchor that actively reinforces the surrounding rock of laminar development. It is a new form of self-anchoring anchor that actively reinforces the rock with developed laminations like an increase nail firmly nailed to the surrounding invulnerable rock layer. The compression stress per meter of the anchor into the borehole is about 25kN, and the anchoring strain generated is roughly equal to the compression force.
Contact Now
Product Description:Hollow grouting anchor cable is suitable for long term support of surrounding rock with medium and good geological conditions, as well as over-head support of highway, railroad, tunnel, slope support, foundation pit support and other projects. Through pressure grouting of the hollow anchor body, it can achieve the purpose of solidifying broken rock body and improving rock body, so as to achieve the purpose of good support.
Contact Now
Anchor Tray DescriptionAn anchor tray is a fixing device used in coal mines that is made from a high-strength steel tube with longitudinal slits. It is installed in drill holes slightly smaller than the diameter of the pipe, which immediately exerts radial pressure on the hole wall and stops the surrounding rock from sliding down. At the same time, the pallets of the anchor tray provide additional load-bearing capacity. In this way, the surrounding rock is under three-way stress.
Contact Now
Description of left-handed non-longitudinal ribbed rebar anchorsMining anchor is a kind of anchor rod commonly used in coal mine underground support compared with the traditional metal anchor rod it is solid quality full length and other strong length can be intercepted according to the specific needs of the rod body is easy to cut the operation is simple and convenient so that you do not make it difficult to use so that the safety of the roadway and other construction sites and construction are very favorable.Anchor technical parameters:yield load（KN）breaking load（KN）Strength Specificationcal
Contact Now
Product OverviewThe longitudinal ribless threaded steel resin anchor executes MT146.2-2011 standard. It is a kind of anchor made by special processing technology, the strength of threaded section is greater than the strength of the rod body, the threaded section has good performance of bending and shearing, it is a new type of anchor for high strength support of shaft.The anchor has high strength, reasonable structure, large tightening force, can automatically adjust the direction of force, increase the binding force on the rock can realize the mechanization of rapid installation.
Contact Now
Product description: Anchor disk:A kind of mine support material, used to cooperate with the support of anchor rods (rods placed in the rock body and in close contact with the rock body), there are round, square, diamond-shaped.Specifications and parameters：Pallet Size（mm）carrying capacity(kn)Pallet Size（mm）carrying capacity(kn)note120x120x5≧100200x200x10≧360Partial specifications120x120x6≧115200x200×12≧420120x120x8≧130250x250×8≧320150x150×5≧135250x250x10≧400150x150x6≧170250×250x12≧440150x150x8≧230300x300x10≧420150x150x10≧290300x300x12≧480120x120x10≧260300x300x14≧520Usage:Anchor disk and ancho
Contact Now
Product Description: Longitudinal ribless threaded steel resin anchor executes MT146.2-2011 standard. It is a kind of anchor made by special processing technology, the strength of threaded section is greater than the strength of the rod body, the threaded section has good performance of bending and shearing, it is a new type of anchor for high-strength support of shafts. The anchor has high strength, reasonable structure, large tightening force, can automatically adjust the direction of force, increase the binding force on the rock can realize the mechanization of rapid installation.
Contact Now
Product DetailsLeft rotating anchor and right rotating anchor are two types of threaded steel anchors. They are named according to the direction of rotation and implement the MT146.2-2011 standard.Anchor rods are the most basic component of roadway support engineering, used to bind the roadway surrounding rock together so that the surrounding rock supports itself. Nowadays, anchor rods are not only widely used in mines, but also used in engineering technology to actively reinforce slopes, tunnels, dams and so on.
Contact Now
Hollow Anchor Rod: Reinventing Underground Rock ReinforcementIntroductionIntroducing the Hollow Anchor Rod, a cutting-edge solution that revolutionizes rock reinforcement in underground engineering. This innovative product boasts unparalleled strength and versatility, making it the ultimate choice for ensuring stability and safety in challenging underground environments.
Contact Now
